Criteria

Text:
Category:
Display:

Results

Viewing 91 to 120 of 206
2018-05-07 ...
  • May 7-8, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Heat transfer affects the performance, emissions and durability of the engine as well as the design, packaging, material choice and fatigue life of vehicle components. This course covers the broad range of heat transfer considerations that arise during the design and development of the engine and the vehicle with a primary focus on computational models and experimental validation covering the flow of heat from its origin in the engine cylinders and its transfer via multiple paths through engine components.
2018-05-08 ...
  • May 8-10, 2018 (8:30 a.m. - 4:30 p.m.) - Greenville, South Carolina
  • August 7-9, 2018 (8:00 a.m. - 4:30 p.m.) - El Segundo, California
Training / Education Classroom Seminars
One of the most important requirements for AS91XX series and other quality standards, is to create, implement and maintain an effective Internal Audit Program. An improperly designed and implemented Internal Audit Program could result in non-conformances leading companies to improperly identifying and describing non-conformances, applying incomplete or inadequate root cause analyses, establishing ineffective corrective actions, implementing incomplete Internal Auditor Qualification Programs, etc.
2018-05-09 ...
  • May 9, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • October 5, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Designing more efficient and robust emission control components and exhaust systems results in more efficient performance, reduced backpressure and fuel penalty, and higher conversion efficiency. This course will help you to understand the motion of exhaust flow in both gasoline and diesel emission control components including flow-through and wall-flow devices such as catalytic converters, NOx adsorbers, diesel oxidation catalysts, diesel particulate filters as well as flow through the overall exhaust system.
2018-05-10 ...
  • May 10-11, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
The sound package materials for vehicle noise control seminar provides a detail and thorough analysis of three different classes of acoustical materials – namely absorbers, barriers, and dampers, how they are different from each other, and acoustical properties that materials should possess for optimum vehicle noise control. The seminar addresses new advances in acoustical materials, primarily in absorption materials that impact the vehicle acoustics. The seminar covers ways to evaluate the acoustical performance of these materials using different test methods, including material, component, and vehicle level measurements.
2018-05-10 ...
  • May 10-11, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Today's necessity for quickly delivering products to market limits product development time and leaves less room for error and 're-dos.' With so many plastic materials available, it is crucial that those involved in product design understand resin properties and how they affect part design and manufacturability. To help you make the best plastic choices the first time, this seminar provides an overview of polymer chemistry, explains the methods for testing properties of plastics and presents a method of systematic selection that will optimize your plastics material selection process.
2018-05-14 ...
  • May 14-16, 2018 (8:30 a.m. - 4:30 p.m.) - Durham, North Carolina
  • August 6-8, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • December 3-5, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Starting with a look at the transmission's primary function -- to couple the engine to the driveline and provide torque ratios between the two -- this updated and expanded seminar covers the latest transmission systems designed to achieve the most efficient engine operation. Current designs, the components and sub-systems used, their functional modes, how they operate, and the inter-relationships will be discussed. A manual transmission display will be used to explain ratios and how they function within the driveline.
2018-05-14 ...
  • May 14-18, 2018 (8:00 a.m. - 5:00 p.m.) - Troy, Michigan
  • November 12-16, 2018 (8:00 a.m. - 5:00 p.m.) - Troy, Michigan
Training / Education Classroom Engineering Academies
View an Interview with Lead Coach Atul Kalia Why a Management Academy? Why should you be interested in this Engineering Management Academy from SAE? The answer to these questions lies in the statistics highlighted by surveys of hiring managers. For example, are you aware that: 28% of internal leadership promotions fail On average, it takes six years before an individual receives any formal training after being promoted to a management position Individual contributors, who are technical experts, are usually natural candidates for promotions to management positions.
2018-05-21 ...
  • May 21-23, 2018 (8:00 a.m. - 5:30 p.m.) - Greer, South Carolina
  • October 15-17, 2018 (8:00 a.m. - 5:30 p.m.) - Greer, South Carolina
Training / Education Classroom Seminars
While a variety of new engineering methods are becoming available to assist in creating optimal vehicle designs, subjective evaluation of vehicle behavior is still a vital tool to deliver desired braking, handling, and other dynamic response characteristics. In order to better prepare today’s engineer for this task, this course offers twelve modules devoted to key the fundamental principles associated with longitudinal and lateral vehicle dynamics.
2018-05-22 ...
  • May 22-23, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Developing vehicles that achieve optimum fuel economy and acceleration performance is critical to the success of any automotive company, yet many practicing engineers have not received formal training on the broad range of factors which influence vehicle performance. This seminar provides this fundamental understanding through the development of mathematical models that describe the relevant physics and through the hands-on application of automotive test equipment. Attendees will also be introduced to software used to predict vehicle performance.
2018-05-22 ...
  • May 22-23, 2018 (8:30 a.m. - 4:30 p.m.) - Livonia, Michigan
Training / Education Classroom Seminars
Providing you have a basic understanding of geometric dimensioning and tolerancing fundamentals, this course teaches an introduction to functional gaging design and how to verify part dimensional requirements using functional gages and other measurement methods. Utilizing the expertise of world-renowned GD&T expert Alex Krulikowski, this course offers an explanation of metrology, the roles of the metrologist and inspector, measurement uncertainty, inspection tools, functional gages, inspection planning and reporting, and simulating datums. Newly acquired learning is reinforced throughout the class with numerous practice problems.
2018-05-24 ...
  • May 24-25, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 12-13, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
The Controller Area Network has become the standard of choice for most automotive manufacturers. Approved for use as an ISO and EPA diagnostic network, its usage continues to grow. This seminar covers the theory and use of the CAN protocol, and its applications in the automotive industry. Details on how the CAN protocol and other standards (J2411, J2284, J1939, ISO 11898, etc.) complement each other will be presented. Attendees will learn about CAN application layers; the latest J1939, J2284, J2411, and IDB standards, regulations, and implementation requirements; and details of device hardware and software interfaces.
2018-05-24 ...
  • May 24-25, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 26-27, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Side impact crashes account for approximately twenty-six percent of all motor vehicle fatal crashes, second only to frontal crashes, according to a report by the National Highway Transportation and Safety Administration (NHTSA). While car companies and suppliers continue to develop new technologies that make vehicles safer, NHTSA rolled out updated safety regulations (FMVSS 214) based on new research studies, making vehicle safety design more and more complex. This seminar is designed to familiarize participants with the engineering principles behind vehicle and restraint designs for occupant safety.
2018-06-04 ...
  • June 4-8, 2018 (8:00 a.m. - 8:00 p.m.) - Troy, Michigan
Training / Education Classroom Engineering Academies
This Academy covers the diesel engine engineering principles and practices necessary to effectively understand a modern diesel engine. Types of engines addressed include naturally aspirated, turbocharged, pre-chamber, open chamber, light duty, and heavy duty. It is an intensive learning experience comprised of lecture and structured practical sessions, including a team-solved case study problem. Evening sessions are included. Attendees will receive a copy of the textbook, Diesel Emissions and Their Control, by lead instructor Magdi K. Khair and W. Addy Majewski.
2018-06-05 ...
  • June 5-6, 2018 (8:00 a.m. - 5:00 p.m.) - Livonia, Michigan
  • October 23-24, 2018 (8:00 a.m. - 5:00 p.m.) - Livonia, Michigan
Training / Education Classroom Seminars
Providing you have an understanding of GD&T fundamentals, this course teaches the thought processes involved in assigning GD&T to components. It will change the way many engineers think about part tolerancing. Utilizing the expertise of world-renowned GD&T expert Alex Krulikowski, the course focuses on what constitutes good and poor drawing practices, common dimensioning methods used in industry, using GD&T to communicate system functions on component dimensions, and the logic of how to apply GD&T to components.
2018-06-06 ...
  • June 6, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 7, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
The principal functions of the pneumatic tire are to generate driving, braking, and cornering forces while safely carrying the vehicle load and providing adequate levels of ride comfort. This seminar explains how tire forces and moments are generated under different operating and service conditions and, in turn, demonstrates how these forces and moments influence various vehicle responses such as braking, handling, ride, and high-speed performance. The content focuses on the fundamentals of tire behavior in automobiles, trucks, and farm tractors, but also includes experimental and empirical results, when necessary.
2018-06-07 ...
  • June 7, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 8, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
One of the most important safety critical components on cars, trucks, and aircraft is the pneumatic tire. Vehicle tires primarily control stopping distances on wet and dry roads or runways and strongly influence over-steer/under-steer behavior in handling maneuvers of cars and trucks. The inflated tire-wheel assembly also acts as a pressure vessel that releases a large amount of energy when catastrophically deflated. The tire can also serve as a fulcrum, both directly and indirectly, in contributing to vehicle rollover. This seminar covers these facets of tire safety phenomena.
2018-06-07 ...
  • June 7-8, 2018 (8:30 a.m. - 4:30 p.m.) - Shanghai, China
  • August 30-31, 2018 (8:30 a.m. - 4:30 p.m.) - Cleveland, Ohio
Training / Education Classroom Seminars
The requirements for producing an FAA approved replacement part can be daunting. Understanding the steps required in the FAA Parts Manufacturer Approval (PMA) process can greatly streamline the approval life-cycle and reduce unnecessary costs and delays, thereby shortening the time and cost to market. This course is designed for those organizations and individuals interested in designing and manufacturing replacement parts for civil aviation aircraft. This two-day course covers the crucial subjects and steps of the FAA-PMA approval process.
2018-06-11 ...
  • June 11-12, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Plastic - any class of synthetically-produced organic compounds capable of being molded and hardened into a specific shape or form. This course is designed to offer a basic understanding of plastics and plastic processing. Using plastics can be simple, but there is much more behind producing high performance plastic parts. This seminar will walk you through the molding process, provide a comprehensive look at the variables in the manufacturing mix, and review characteristics of typical automotive plastics such as PP, PVC, ABS, and more.
2018-06-13 ...
  • June 13-15, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • October 10-12, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Societal and regulatory demands to lower emissions and increase engine-operating efficiencies have forced engine designers to adopt new technologies and control strategies. This has resulted in dramatic evolutions of the technology of internal combustion engines and their support systems in recent years. These operational management strategies have evolved into more robust control systems and sensory packages, which in turn has driven the need for more accurate and specific information being communicated between the various systems found within a modern automobile.
2018-06-18 ...
  • June 18-19, 2018 (8:30 a.m. - 4:30 p.m.) - Hamburg, Germany
Training / Education Classroom Seminars
The rapidly evolving demand for cost reductions and shrinking budgets makes the application and use of automated processes within the aerospace and space industries a necessity. While some view aerospace automation as the solution to reducing costs, others view automation technologies and processes as something that should be avoided when possible. Misunderstandings and assumptions about these complex systems can result in the improper selection and application of these systems, often leading to undesirable interactions with other elements of the assembly process and potentially, project failure.
2018-06-18 ...
  • June 18-19, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Engine valvetrain systems have become more capable and increasingly more compact in the quest to improve efficiency. The developments parallel the advancements in other key engine components such as fuel injection or spark systems, turbocharging, aftertreatment, base engine and controls. While the gasoline sector has seen a steady rise in the adoption of Variable Valve Actuation (VVA), Diesel systems have lagged behind and only a few systems have seen production. The level of VVA activity however in the Diesel sector is beginning to increase as tighter regulations of CO2 emissions approach.
2018-06-18 ...
  • June 18-20, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 28-30, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
EDR’s are not new, but are becoming more prevalent in part due to a new federal regulation. 49 CFR, Part 563, which affects vehicles produced after September 30, 2012, will result in a standardized and publicly available EDR in 90% of new vehicles. Accident Reconstructionists frequently have trouble reconciling EDR data with other data sources, and improvements in ABS technology result in fewer tire marks visible at the scene of crashes to allow calculation of pre-crash speeds without an EDR.
2018-06-20 ...
  • June 20, 2018 (8:30 a.m. - 4:30 p.m.) - Hamburg, Germany
Training / Education Classroom Seminars
The challenges associated with using composites as a replacement for aluminum reside primarily in the complex manufacturing processes and technologies for fabricating composite parts. The high cost of composites material and its manufacturing complexity have been inhibitors to the wide transfer of this technology to the non-aerospace market. The search for solutions to high manufacturing costs and efficient manufacturing processes have resulted in intense research by government, aerospace industry companies, and space agencies worldwide.
2018-06-20 ...
  • June 20-21, 2018 (8:30 a.m. - 4:30 p.m.) - Hamburg, Germany
Training / Education Classroom Seminars
The transportation industry, including motor vehicles, aircraft, rail, marine, commercial, off-road and defense vehicles, as well as infrastructures, energy sectors, raw materials, manufacturing, health and food industries all experience significant issues with corrosion which results in billions of dollars of loss each year. Corrosion education and prevention is essential to improve and increase the service life of parts and components which may have a significant impact on the economy of various industries and nations.
2018-06-20 ...
  • June 20-22, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Fuel composition has had to change with the advent of more stringent emission regulations. Reformulated gasoline (RFG), for example, is vastly different from gasoline of even ten years ago. Tightening regulations on diesel emissions will dramatically change both diesel fuel and engine design. This three-day seminar will review the fundamentals of motor fuels, combustion and motor power generation. The primary content of the course provides a basic introduction to the technology, performance, evaluation, and specifications of current gasoline, diesel, and turbine fuels.
2018-06-22 ...
  • June 22, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Effective decision making is critical to maximizing profit/minimizing expenses, return on capital spending, and operational efficiency. To understand the impact of decisions that affect the enterprise, professionals at every level must secure and integrate relevant cross-functional information. Register for this seminar and learn skills needed to base decision making on solid business knowledge and sound financial principles instead of on emotion or "your gut." The instructor walks you through the tenets of structured decision-making and teaches a step-by-step approach to make practical, effective decisions.
2018-06-25 ...
  • June 25-27, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • November 12-14, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
On-board diagnosis of engine and transmission systems has been mandated by government regulation for light and medium vehicles since the 1996 model year. The regulations specify many of the detailed features that on-board diagnostics must exhibit. In addition, the penalties for not meeting the requirements or providing in-field remedies can be very expensive. This course is designed to provide a fundamental understanding of how and why OBD systems function and the technical features that a diagnostic should have in order to ensure compliant and successful implementation.
2018-06-25 ...
  • June 25-26, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Design of Experiments (DOE) is a methodology that can be effective for general problem-solving, as well as for improving or optimizing product design and manufacturing processes. Specific applications of DOE include identifying proper design dimensions and tolerances, achieving robust designs, generating predictive math models that describe physical system behavior, and determining ideal manufacturing settings. This seminar utilizes hands-on activities to help you learn the criteria for running a DOE, the requirements and pre-work necessary prior to DOE execution, and how to select the appropriate designed experiment type to run.
2018-06-27 ...
  • June 27-28, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Seminars
Design for Manufacturing and Assembly (DFM+A), pioneered by Boothroyd and Dewhurst, has been used by many companies around the world to develop creative product designs that use optimal manufacturing and assembly processes. Correctly applied, DFM+A analysis leads to significant reductions in production cost, without compromising product time-to-market goals, functionality, quality, serviceability, or other attributes. In this two-day seminar, you will not only learn the Boothroyd Dewhurst Method, you will actually apply it to your own product design!
2018-07-09 ...
  • July 9-14, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
  • September 24-29, 2018 (8:30 a.m. - 4:30 p.m.) - Troy, Michigan
Training / Education Classroom Engineering Academies
Pilot Dates: August 28 to October 6: Online on-demand modules accessible through SAE LMS October 9 to 11, 8:30 a.m. to 4:30 p.m. Classroom modules, SAE Troy Office: Product Development Process and Project Management, Critical Thinking and Problem Solving, Personal Time Management and Workflow Efficiency, and Record Keeping and Documentation October 16 to 18, 8:30 a.m. to 4:30 p.m.
Viewing 91 to 120 of 206